Skip to product information
1 of 6

YFROBOT

YFROBOT Metal Gearmotor GB37-3530 12V with 16 CPR Encoder Hall speed measurement

YFROBOT Metal Gearmotor GB37-3530 12V with 16 CPR Encoder Hall speed measurement

Regular price $39.00 USD
Regular price Sale price $39.00 USD
Sale Sold out
ratio

Overview

Measuring 37 mm (1.46″) in diameter, these brushed DC gearmotors are the largest and most powerful we carry. They are available in a range of gear ratios from 6.3:1 to 150:1 and with 12 V  motors, and all versions are available with integrated 64 CPR quadrature encoders on the motor shafts. The 12 V motors offer approximately the same performance at their respective nominal voltages. Its motor shaft is a 6mm D-shaft.

In general, these kinds of motors can run at voltages above and below the nominal voltages; lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor.

The gearboxes are composed mainly of spur gears, but they feature helical gears for the first stage for reduced noise and improved efficiency:

Using the Encoder

A two-channel Hall effect encoder is used to sense the rotation of a magnetic disk on a rear protrusion of the motor shaft. The quadrature encoder provides a resolution of 64 counts per revolution of the motor shaft when counting both edges of both channels. To compute the counts per revolution of the gearbox output, multiply the gear ratio by 64. The motor/encoder has six color-coded, 8″ (20 cm) leads terminated by a 1×6 female header with a 0.1″ pitch, as shown in the main product picture. This header works with. If this header is not convenient for your application, you can pull the crimped wires out of the header or cut the header off. The following table describes the wire functions:

Color Function
Red motor power (connects to one motor terminal)
Black motor power (connects to the other motor terminal)
Green encoder GND
Blue encoder Vcc (3.5 – 20 V)
Yellow encoder A output
White encoder B output

 

The Hall sensor requires an input voltage, Vcc, between 3.5 and 20 V and draws a maximum of 10 mA. The A and B outputs are square waves from 0 V to Vcc approximately 90° out of phase. The frequency of the transitions tells you the speed of the motor, and the order of the transitions tells you the direction. The following oscilloscope capture shows the A and B (yellow and white) encoder outputs using a 12 V motor at 12 V and a Hall sensor Vcc of 5 V:

By counting both the rising and falling edges of both the A and B outputs, it is possible to get 64 counts per revolution of the motor shaft. Using just a single edge of one channel results in 16 counts per revolution of the motor shaft, so the frequency of the A output in the above oscilloscope capture is 16 times the motor rotation frequency.

Precautions

  • This product does not have waterproof function, and it is strictly prohibited to use in water or damp environments.
  • Short circuit between positive and negative poles is prohibited.
  • Obtain information through email. 

Motor parameters

Gear  ratio  1:xx

Rated voltage (V)

No Load speed (rpm/min)

Load speed (rpm/min)

Rated torque (kg.cm)

Current rating (mA)

Load torque (kg.cm)

Stall current (mA)

1:10

6

550

400

0.48

700

2.6

4000

12

1100

750

1.2

1100

6.5

6500

1:18.8

6

292

232

0.9

700

4.5

4000

12

585

480

2.2

1100

12

6500

1:43.8

6

126

95

2.0

700

12

4000

12

251

200

5.2

1100

25

6500

 

Electrical characteristics

Specification

Symbol

Test Condition

Min

Typical

Max

Unit

Input Voltage

Vcc

--

2.7

5

5.5

V

Output Saturation Voltage

Vce(sat)

VCC=14V; IC=20mA

-

300

700

mV

Output Leakage Current

Icex

VCC=14V; VCC=14V

-

<0.1

10

A

Input Current

Ice

VCC=20V, output open

-

5

10

mA

Output Rise Time

Tr

VCC=14V; RH=820Ω;CH=20pF

-

0.3

1.5

S

Output Fall Time

Tr

VCC=14V; RL=820Ω;CL=20pF

-

0.3

1.5

S

Operating Temperature Range

Topr

 

0-85

 

Installation method

View full details

Introduce your content

Answer your customers' common questions

List a frequently asked question

Then provide an answer that will help your customer make an informed purchase.

List another frequently asked question

List another frequently asked question